Request a Quote

Home / Products / DOT Push-In Fittings (Brass) / D.O.T Push In Bulkhead Connector

D.O.T Push In Bulkhead Connector — representative product photo, full product on white background
DOT Push-In (Brass)

D.O.T Push In Bulkhead Connector

1583 · Brass / composite programme · Built to FMVSS 571.106 · SAE J2494 · for SAE J844 Type A & B nylon tubing.

This is a representative photo of the series/type — it does not show a specific size. The specification for this product is in the table on this page.

About this fitting

DOT Air Brake Bulkhead Fitting2 is a bulkhead fitting in WAVE's DOT Push-In (Brass) family. It passes an air line through a panel — the trailer frame, floor or a cabinet wall — anchoring and sealing the line at the pass-through point with its locknut. The all-brass body and collet grip SAE J844 nylon tube over a stainless support, with a Buna-N seal — push in to seal, pull the collet to release for service. It is made for 1/4″ – 3/4″ tube, with a threaded end in the NPTF 1/8″ – 1/2″ range. Family working range: 250 psi, −40°F to +200°F. The exact variant is picked from the size options on this page and confirmed against the factory catalogue at inquiry.

Select a size

Inquire on this modelCross-reference a number
Specification — DOT Air Brake Bulkhead Fitting2
Model1583
FeaturesBrass Collet; Buna N O-ring; Stainless Steel Tube Support; Meets D.O.T. FMVSS571.106; Meets SAE J2494 & SAE J2494-3
MaterialBrass collet, Buna N O-ring, stainless steel tube support
StandardDOT FMVSS571.106; SAE J2494 & SAE J2494-3;Meets D.O.T. FMVSS571.106;Meets SAE J2494 & SAE J2494-3
Compatible tubingSAE J844 Type A & B nylon tubing
Reference Part No.1583DOT

Dimensions are reference data — please confirm at inquiry.

Size table — DOT Air Brake Bulkhead Fitting2

PART#TUBE O.D×Thread NPTFCBEL
1583-DOT-6D3/8×1/21-3/81"-141-1/41.99
1583-DOT-8D1/2×1/21-3/81"-141-1/41.99

Dimensions are reference data — please confirm at inquiry.

Features
  • Panel mounting with a locknut — the line is anchored where it passes through
  • Ends: Push-in tube socket × Push-in tube socket — through a panel
  • The all-brass body and collet grip SAE J844 nylon tube over a stainless support, with a Buna-N seal — push in to seal, pull the collet to release for service.
  • Buna-N O-ring seal
  • This page covers DOT Air Brake Bulkhead Fitting2 (1583) — select its size above and that exact variant is carried into the inquiry
Applications

DOT Air Brake Bulkhead Fitting2 — It passes an air line through a panel — the trailer frame, floor or a cabinet wall — anchoring and sealing the line at the pass-through point with its locknut. In WAVE's DOT Push-In (Brass) family it serves: Tractor and trailer air lines · valves and air tanks · brake chambers · frame-to-axle runs · dash controls.

Compatible tubing

For DOT Air Brake Bulkhead Fitting2, the compatible line is: SAE J844 Type A & B nylon air brake tubing, 1/4″–3/4″ O.D.. The tube end of this bulkhead fitting takes that line (1/4″ – 3/4″); the threaded end (NPTF 1/8″ – 1/2″) mates with its port and does not change the line it serves.

The size options at the top of this page list only the sizes this configuration is made in — each threaded option is a tube × thread combination.

Reference Part No.: the 1562-DOT family is published with AQ62DOT · 62PMT · 1862 · DQ62DOT — check your number in the cross-reference. “Replacement for” describes fit and function only.

Related products — same family

← Back to DOT Push-In Fittings (Brass)